E-GDO-1000 Garage Door Operator: Frequently Asked Questions

This guide addresses the most frequently asked setup and programming questions for the E-GDO-1000 garage door operator. It’s designed for installers and technicians who need fast, reliable instructions while on site. 

Each section tackles a specific programming function, walking you through the steps to complete with ease, whether you're setting travel limits, pairing transmitters, adjusting safety settings, or activating advanced features like Wi-Fi control and vacation mode. 

Use this as your go-to reference to streamline installation and ensure everything works as intended. 

• How do I set the travel limits on the E-GDO-1000?

• How do I pair transmitters to the E-GDO-1000?

• How do I set the safety reverse force?

• How do I set the auto-close feature?

• How do I enable or disable the photobeam feature?

• How do I set up Wi-Fi control for the E-GDO-1000?

• How do I set the partial opening function?

• How do I set the lock button on the transmitter?

• How do I set door open only mode?

• How do I change the door closing speed?

• How do I set vacation mode on the operator?

  
  

How do I set the travel limits on the E-GDO-1000? 

1. Press and hold the SET button until the LED displays 01. 

2. Use the UP button to move the door to its upper limit. Fine-tune using UP or DOWN. 

3. Press SET – the display will switch to 02. 

4. Now, use the DOWN button to move to the lower limit. Fine-tune as needed. 

5. Press SET again. The opener will run a full cycle to store limit positions and auto-calibrate force. 

Display shows --: No travel limits set. 

Display shows FF: Travel limits successfully saved. 

How do I pair transmitters to the E-GDO-1000? 

1. Hold the UP button until the LED dot flashes.  (Fig a)

2. Press any button on the transmitter twice. The LED will flash quickly and turn off – pairing successful. 

3. To clear all transmitters, hold UP for more than 8 seconds until the LED shows 00. (Fig B)

   
   
   
   
   
   

How do I set the safety reverse force? 

1. Hold SET until the LED shows 03. 

2. Adjust force using: UP to increase (Max: 09), DOWN to decrease (Min: 01) 

   
   
   
   

   Important: Levels 04–09 require a working photobeam. Without one, only use 01–03. 

   
   

How do I program the auto-close feature? 

1. Hold SET until the LED shows 04. 

2. Use UP/DOWN to adjust time (1 = 10 sec, 2 = 20 sec... max = 54 = 540 sec). 

3. Press SET to confirm. 

Display 0: Auto-close disabled. 

Note: Photobeam must be installed and working before activating auto-close.

How do I enable or disable the photobeam function? 

1. Hold SET until the LED shows 05. 

2. Press: 

3. UP for 1: Enable photo beam. 

4. DOWN for 0: Disable. 

5. Press SET to confirm.

   
   

Note: If enabled but not physically connected, the door won’t close. Please ensure that the connected infrared sensors is controlled by pulse control photobeam, and wired as seen in figure 15. 

How do I set up Wi-Fi control for the E-GDO-1000? 

Things to know before you start: 

• Travel limits must be set. 

• Only 2.4GHz Wi-Fi is supported. 

• Only one main account can be linked (but can invite others). 

  
  

Step-by-step: 

1. Hold DOWN until LED shows 0. 

2. Press UP: 

   a.Display 01: Enter Wi-Fi connect mode. 

   b.Display 02: Reset Wi-Fi. 

3. Press SET to confirm the selected mode. 

1. Download Smart GDO app (iOS/Android) → Register/Login → Add Device → Choose "Garage" → Wait for fast-blinking indicator. 

2. In app: Connect to Wi-Fi, enter password, then press “Confirm.” 

   
   

   a. LED will show FF. and blink during pairing. 

   b. After success: press “Done.” 

   c. If failed: reset and retry. 

   
   

   

   
   
   
   

   

   
   
   
   

To remove device: 

• Option 1: Remove via app. 

• Option 2: Reset GDO (Hold DOWN until 0, then UP until 2, then SET). 

Accessing and Configuring Special Features 

The E-GDO-1000 includes several advanced functions designed to meet different user needs. Here's how to access each feature: 

Partial Opening Function 

Allows the door to open to a predefined height. 

• Hold UP + DOWN together until the LED displays 06. 

• Press SET. 

• Use UP/DOWN to select height (1 = 10cm … 20 = 200cm). 

• Press SET to confirm. 

• 0 disables the feature. 

  
  

Note: The partial height must be less than the full open limit. 

Lock Button on Transmitter

Disables the remote control after the door is fully closed. 

• From 06, press UP to display 07. 

• Press SET. 

• Press: 

• UP = Enable (1) 

• DOWN = Disable (0) 

• Press SET to confirm. 

  
  

Function: After 5 seconds of full closure, the remote is locked. Press the unlock button first to use it again. 

Door Open Only Mode 

Restricts the remote to open only when enabled. 

• Press and hold UP and DOWN together until the display shows figure 06, then press UP to display 08. 

  
  

Press SET to confirm the door is in open-only mode 

Press: 

• UP = Enable (1) 

• DOWN = Disable (0) 

• Press SET to save. 

  
  
  
  

Closing Speed Selection 

Adjusts the speed at which the door closes. 

• From 06, press UP to display 09. 

• Press SET. 

Choose: 

• UP = Normal speed (L) 

• DOWN = High speed (H) 

• Press SET to confirm. 

• Note: High-speed mode requires a compatible high-speed motor and active photo beam. 

Vacation Mode

Locks out all remotes and outdoor keypads while active. This is ideal for extended absences or security-sensitive periods. 

• From 06, press UP to display 11. 

• Press SET. 

Press: 

• UP = Enable (1) 

• DOWN = Disable (0) 

• Press SET to confirm. 

This feature can also be activated through the app. 

Still stuck? 

If functions are not responding as expected, ensure all wiring is correct, sensors are properly aligned, and travel limits are set. Refer to the full installation manual or contact technical support at technical@ellard.co.uk